1967 - 1969 Camaro Parts - Identifying a First Generation Z28 - Steves Camaro Parts San Bruno - 650-873-1890

The Chevy Camaro Z28 was produced in the following years '67-'74, '77-'88, ('88-'90 IROC), '91-'02. The only true years a Z28 was not available in any form or fashion was 1975 and 1976. Basically, the Z28 option was a performance package with some nice looks added to help identify them before you got to see their tail lights. Since the Z28 was a performance package, the engine is one of the most important parts of a Z28 Camaro. In most cases the original Z28 engine is required to identify the car as possibly being a true Z28. Also, remember that having the original engine doesn't mean the rest of the car is still original. Check everything including dates, castings and partial VIN's. If the complete VIN says it was originally a 6 cylinder Camaro then you can guarantee it was not a Z28 so be sure to check the VIN. Unfortunately, these days it is so easy to fake almost everything on a Camaro - the more you know the better off you will be. Here is a good old saying that is never more true than for this ... if we had a nickel for every time someone said they had a Z28 Camaro (but did not) we would be filthy rich by now.

Identifying a First Generation Z28:
The best place to start to try to verify a first gen Z28 is by checking the engine codes and dates. We hope more people read this before buying a Camaro not after buying that so called Z28. All had a 302 cubic inch engine with a suffix code MO or MP in '67, MI or MO in '68 and DZ in '69. To get the 302 engine Chevy took a 283 crank and put it in a 327 block. Some people say Chevy put the crank in a 350 block but since 1967 was the first year for 350's and 302's and both used the 327 block it is better to say they used a 327 block. A 302, 327 and 350 block are exactly the same except for the number of main bolts which would depend on the application and the year. The 1969 302's had 4 bolt mains. The 1967 and 1968 302's did not have 4 bolt mains. They were in fact 2 bolt main blocks used in '67 and '68 302's. In 1967 they are small journal blocks and in '68 and '69 they went to large journals. The reason for the Z28 was to compete in SCCA Trans-Am Challenge Series. The engine requirements to race in SCCA was limited to 305 cubic inches. All had 4 speed Muncie manual transmissions. All had power front disc brakes at least. All had 12 bolt rear ends but didn't have to be posi. None had A/C. None were factory convertibles except one beautiful '68 Z28 was a convertible which was made for the head of Chevrolet at the time (Pete Estes) and if you own it email us a picture and all the info you can please! Just remember badges do not a Camaro Z28 make. There is NO code in the VIN that recognizes a Z28 in any first generation Camaros. Late '69 Camaros had an "X" code on the trim tag though. A Protect-o-plate can be helpful in identifying a first gen. Z28 but be careful because there are places that make reproductions of both trim tag and protect-o-plate. Before emailing us in the hopes that we know some secret to identifying Z28's check the engine codes given below. If the Camaro doesn't have the original engine then finding out whether it was a Z28 at one time just got that much harder and in most cases impossible.

YearTrim Tag Code?Check Engine Code Table or get Help
VIN Engine Code?
1967YESMO or MP
1968NONEMI or MO
1969Some X codesDZ

Common things most people erroneously think makes a First Gen Camaro a Z28 and we get asked about all the time. Also known as FAQ's on Z28 Camaros being a true Z28.

Required for a Z28
Available on base Camaros
Easily Purchased and Added
Special EngineYes (see above)NoNO! Very hard to fake especially the casting number and casting date
Z28 EmblemsYes (some were "302" and some were "Z28")NoVery much YES!
Special HoodNot all but mostNoYes!
Front disc brakes Yes (Brakes could NOT be front drum brakes)Yes - but most got drum brakes.Yes! Check that they are not after market though.
Special Instruments - Amp, temp, oil pressure, fuel, clock, tachNo - that's right NO not required.Yes - just required V8 and ConsoleYes! They were AC gauges. Also tach's were dealer installed or factory late in 69.
12 bolt rear endYes but didn't have to be a posiYes - but check dates of rear endNot easy to find one dated for a specific Camaro build date.
Automatic (ANY)NO! Automatic was not available on any first gen Z28YesEasy to change to 4 speed but not easy to fake correct 4 speed trans with partial VIN. Also be sure to check manual transmission. The Z28 Trans was not a Saginaw it was a Muncie. Saginaw was the "low" performance manual trans.
"X33" or "X77" Code on trim tag on 1969's onlyYes but for late style Norwood assembled '69 Camaros only! (No so called "X" codes on Van Nuys assembled Camaros)No - Base Camaros got "X11"Not easily added but check VIN to make sure it was a V8 because trim tags are getting swapped out. Also have seen people selling reproduced trim tags so watch out.

Source: www.chevy-camaro.com


Tags: camaro part, camaro parts, Camaro restoration parts, 69 camaro, 1969 camaro, aftermarket camero parts, chevrolet camaro, ss, z28, rs, chevrolet, restoration, 68 camaro, chevy, 67, 69, f-body, camaro, chevy camaro, chevrolet camaro, gm, z-28, 350, ls1, z/28, pace car, camaro ss, 69 camaro, first generation, copo, fbody, yenko, 67 camaro, 68 camaro, musclecar